What did you do to your turbo today?

Chip Birks · Post by **Chip Birks** » Sun Feb 15, 2015 11:45 am

Are they the same as mine? Have you received them yet?

Post by **seabeebuggy** » Mon Apr 27, 2015 6:10 am

Well after 10 years? i pulled my carbs off for a rebuild. I just could not get the car to run with out spraying fuel. Ordered rebuild kits from e bay. I wanted to get them from CB performance but they wanted 18$ to ship. No thanks.

58Dub · Post by **58Dub** » Sun Aug 02, 2015 9:11 am

did some engine mock up yesterday.... slowly getting there.

madmike · Post by **madmike** » Mon Aug 31, 2015 6:15 am

Drove my 2276 yesterday, while my son watched&listened he's more up on turbocharging then I

once in a while I heard a bang

just when I shift to 4th,, it's was the wastegate

slicks on a sandy/dirt road is fun

still have stock trans

stage I and a sprung center 4 puck

this sunday drags at Boyne City will be the 2nd time I've run it on pavement 18lbs in the slicks will help save the trans i hope
I'll just have some V8's

yes, my lil' crew chief will be helping, not quite 2yrs old and his 2nd drag event

,, I'll post the results next Monday

Thanks for all the help guys!!!!
Madmike

madmike · Post by **madmike** » Tue Sep 01, 2015 4:52 am

Had a huge puddle under the 4qt sump

Must of smacked a 'sex Stone' on my road again

yepper, even broke the main stud holding the pick-up tube in place

always right before the big race up here,hope i can fix before Sunday

can I get away with just a 1 1/2 sump?

Fiatdude · Post by **Fiatdude** » Tue Sep 01, 2015 6:35 am

Drag racing will allow you to get away with a smaller sump -- the bigger sump is needed for cruising for temp control and road racing to keep some oil around the pickup

madmike · Post by **madmike** » Wed Sep 02, 2015 4:41 am

I had to change the 4qt for a 1/12 yesterday

PITA in the car but it's done

good to know Fiatdude

hate to spin a 'Carrillo' rod bearing

madmike · Post by **madmike** » Wed Sep 02, 2015 5:12 am

Tip:app. for Deep sump,, for a pick-up tube extension I use a old aluminum empi adjustable/spring loaded tube(junk anyhow) cut to fit
they are perfect for this

seal/attach with JB weld,no more running to the hardware for conduit that don't fit right

hope this help someone? ,I've spent hours looking for the right size tubing before

Madmike

58Dub · Post by **58Dub** » Fri Apr 08, 2016 6:58 am

doing a little mock up with the CB turbo header

sideshow · Post by **sideshow** » Fri Apr 08, 2016 10:00 pm

Gasp, somebody stole ye-ar oil cooler hole!

58Dub · Post by **58Dub** » Mon Apr 11, 2016 3:05 pm

sideshow wrote:Gasp, somebody stole ye-ar oil cooler hole!

lol... yes, Michigan is a high theft state!

dave t · Post by **dave t** » Tue Apr 12, 2016 6:27 pm

WBX case?

58Dub · Post by **58Dub** » Wed Apr 13, 2016 6:08 am

madmike · Post by **madmike** » Fri Jun 10, 2016 4:37 am

I drove the piss out of it yesterday .about 60+ miles

with the 'cruise' motor 1915cc 45 dcoe draw threw,, about 14mpg ,, with playing

madmike · Post by **madmike** » Sun Jun 12, 2016 6:25 am

Time to clean out the Garage.
My old Turbo set up is for sale see pic above^
T04 carbon sealed Roto-Master ,turbine 68a/r compressor 60a/r
header & wastegate all for $850. adds on theslamba

Shoptalkforums.com

What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?

Re: What did you do to your turbo today?