A-1 installed pics in Ghia...Excuse the Rust :D
- Ephry73
- Posts: 3369
- Joined: Fri Mar 02, 2001 12:01 am
A-1 installed pics in Ghia...Excuse the Rust :D
http://pg.photos.yahoo.com/ph/kateko69/ ... d8&.src=ph
The other pics are here(Also posted new ones too):
http://pg.photos.yahoo.com/ph/kateko69/ ... /my_photos
Hope this helps. As you can see, there is plenty of room to move the collector angle up a few degrees( I'll say about 10*) to give more ground clearance. Also, the muffler could be angled up and rotated on its axis a few degrees, and give even more clearance, without sacrificing power, or design.
ALso notice the sanding done to clear pipes, and make them able to slide in their corresponding bores.
Ephry
P.S. Jake, maybe you can tell Tiger.
P.S.S The oil is WD-40 I used to clean the pipes
The other pics are here(Also posted new ones too):
http://pg.photos.yahoo.com/ph/kateko69/ ... /my_photos
Hope this helps. As you can see, there is plenty of room to move the collector angle up a few degrees( I'll say about 10*) to give more ground clearance. Also, the muffler could be angled up and rotated on its axis a few degrees, and give even more clearance, without sacrificing power, or design.
ALso notice the sanding done to clear pipes, and make them able to slide in their corresponding bores.
Ephry
P.S. Jake, maybe you can tell Tiger.
P.S.S The oil is WD-40 I used to clean the pipes
- Ephry73
- Posts: 3369
- Joined: Fri Mar 02, 2001 12:01 am
- somordha
- Posts: 57
- Joined: Tue Nov 06, 2001 12:01 am
- Ephry73
- Posts: 3369
- Joined: Fri Mar 02, 2001 12:01 am
You mean like a zoom out shot? I can get one by tomorrow. I need to go to get an apraisal on rust repair for the car. Where my car is parked now I cannot get too far, or get good light. I will definitely get that done tomorrow. There's good ground clearance for sure. Like I said, for us Ghia owners, a different collector pitch and muffler angle will be incredibly better. Also, the muffle rpipe sticks back considerably, a la Cal-look. keep your rear bumper, and you'll be fine.
Ephry
Ephry
-
- Posts: 602
- Joined: Sat Apr 24, 2004 12:18 pm
Rats - I have square ports.Ephry73 wrote:Oval. The head pipes are quite nice actually, since they use stock flanges, which in my opinion offer the best sealing possible. I was not going to get rid of those, but I have too many parts at home, waiting to get sold. Anything else you may need?
Ephry
Basically, I need everything from the head on out. For that matter, I need a bunch of other stuff as well, but I'm just cherry picking now.
- Ephry73
- Posts: 3369
- Joined: Fri Mar 02, 2001 12:01 am
- Ephry73
- Posts: 3369
- Joined: Fri Mar 02, 2001 12:01 am
Ok, here are the numbers. Sorry about the delay. It's been one of those weeks.
from collector bend, to collector opening, 10.25"
from collector merge, to radial bend of muffler pipe, 16.5"
from pulley/crank bolt centerline, to top of collector, 3.5"
from edge of case, just below the pulley, to collector merge, 3.5"
between the oil filter and the #3#4 pipes, 1.25"
Ephry
from collector bend, to collector opening, 10.25"
from collector merge, to radial bend of muffler pipe, 16.5"
from pulley/crank bolt centerline, to top of collector, 3.5"
from edge of case, just below the pulley, to collector merge, 3.5"
between the oil filter and the #3#4 pipes, 1.25"
Ephry