Page 3 of 12
Posted: Wed Sep 05, 2007 6:02 pm
by Leatherneck
I'll bring it to Little Sahara in Oct.
Posted: Wed Sep 05, 2007 6:49 pm
by SANDDUDE
allsierra123 wrote:I am looking for a non doghouse 1600 fan shroud without the little heat things sticking off of it.
Got it!
W/ box this thing will not weigh more than 10 lbs
NO dents just needs paint!
PM me you zip for shipping total
Posted: Thu Sep 06, 2007 1:56 am
by 69bajakid
i have a 7 peice baja kit that i have never seen on a car..it does have the "delux" recessed hood.. crack in nose piece..very easy fix..no missing chunks or holes..if you wanna pay shipping i will pack it up. and find a cheap way to send it.
i will dig tomorrow and see what else i have.
Posted: Thu Sep 06, 2007 4:03 pm
by TCoville
i got a '64 swing axle tranny drum to drum free to anyone who wants to pick it up thousand oaks 91362. send me a pm any weekend is good for the most part.
Posted: Thu Sep 06, 2007 5:39 pm
by allsierra123
I will take that shroud.Thanks man.
Posted: Thu Sep 06, 2007 9:02 pm
by Class 11 streeter
deleted
Posted: Thu Sep 06, 2007 9:49 pm
by allsierra123
if you send one UPS its a little over $100 to send. I think that was minus the rear fenders.
Posted: Fri Sep 07, 2007 9:16 am
by turboblue
allsierra123 wrote:I will take that shroud.Thanks man.
Is that a 36hp shroud?
I'm thinking it's too narrow for a 1600 and uses the thinner fan too.
Some aftermarket versions will fit though.......
Posted: Fri Sep 07, 2007 9:23 am
by Leatherneck
Ok what is the difference in a 36 and 40 shroud? I hate sounding stupid but man I am getting good at it
Posted: Fri Sep 07, 2007 10:47 am
by turboblue
Leatherneck wrote:Ok what is the difference in a 36 and 40 shroud? I hate sounding stupid but man I am getting good at it
OK don't repeat this as the gospel but I think some 36 HP 1200cc engines had no provisions for the fresh air heat. (outlets on the fan housing).
Later 36 and 40 HP, both still 1200cc had the outlets but are narrower than the 13-1600cc engines.
Fan shrouds were narrower I am thinking.
Someone who knows the older stuff better than me needs to jump in here.........
Posted: Fri Sep 07, 2007 4:20 pm
by bajaherbie
it looks like the shroud on my old 40 engine. it was a '62 and had no vent tubes. i think it had "stale air" heater boxes. then again, i'm no eggspert.
turboblue is right abput the 36 shrouds having thinner fans, but i don't know when they went to the slightly wider fan.
Posted: Fri Sep 07, 2007 6:25 pm
by runslikeapenguin
6 over link pin beam with bigger shock towers (not sure how big) with bilstein shocks and gusseted spindles. only down side is its pretty much compleatly frozen up. and the spindles have to be re built.
Posted: Fri Sep 07, 2007 7:32 pm
by allsierra123
Dang after i move out of state. Im going to end up doing the same setup with mine.
Posted: Thu Sep 13, 2007 3:42 pm
by KBWAKESK8
im looking for a spring pack out of a stock linkpin beam.
Posted: Tue Oct 30, 2007 2:30 pm
by KBWAKESK8
bump